Content

• Advice

Gently wipe the iron surface until clean. Don't forget to scrub the steam vents to remove dirt. If necessary, wipe off the remaining surface of the iron.

• Note: The vinegar-salt mixture can also remove burns from your iron.
• If you cannot remove the residue on the iron with a rag, you can use a scouring sponge or sponge to scrub. Be sure not to use metal materials to avoid scratching your iron.

advertisement

Method 2 of 4: Use baking soda

1. 

   
   
   Mix baking soda with water. Mix 1 tablespoon (15 ml) of water with 2 tablespoons (30 g) of baking soda. Mix mixture in a small bowl until a dough is formed.

2. 

   Use a spatula to spread the mixture on the iron surface. Focus on areas where there is a lot of residue that accumulates, making sure to spread the steam vents as well. Do not apply too thick; you should only coat the iron evenly.

3. 

   Wipe off the dough with a damp rag. Don't be afraid to scrub the areas with stubborn dirt stains. Wipe until the dough and the blemishes are gone.
   • Baking soda often leaves white streaks on your iron. You may need to wipe the stain with a damp cloth several times.
   • Wash the rag after each wipe to let the baking soda come off the line.

4. 

   
   
   Clean the steam spray holes with a cotton swab. Soak a cotton swab in water and clean the steam vents. You should scrub well to remove deposits and baking soda mix.
   • Take the iron to the sink after wiping the steam vents to empty any water that may have entered them.
   • Do not use paper clips or other hard metal objects, as these can scratch the steam vents of the iron.

5. 

   Fill the iron with water and make a piece of cloth. Be sure to use a piece of cloth that you are not afraid of spoiling, as some leftover stains may stain the fabric. Turn on the iron in the hottest mode and last for a few minutes; Clean water will wash away any remaining dirt.
   • Fill the sink with any excess water from the iron.
   • Let the iron dry. Remember not to place your iron on damaged surfaces, as sediment may drip down from the steam vents.
   • Use a clean rag to try it out before applying to other fabrics. Thus, if there is residue left on the iron, your clothes will not be damaged.
   advertisement

Method 3 of 4: Use other household products

1. 

   
   
   Mix warm water and mild detergent in a bowl. The amount of soap needed will depend on the amount of residue on the iron. Remember that the solution will be much thinner when it is done, than the soap you would normally use in dishwashing.

2. 

   Dip a cotton cloth in the soap solution and wipe the iron. Be sure to scrub the spray holes more than water, as this is a place where sediment is common. You can also wipe the rest of the iron to remove any stains.
   • This solution is used to clean the table top is teflon non-stick aluminum is the best, because like other teflon coated kitchen utensils, the surface of the iron covered with this material has anti-stick effect but is easy to scratch.

3. 

   Use a damp rag to clean the iron. Clean the iron until the soap stains are gone. Set the iron upright on the table and allow to dry; You can put a towel underneath to absorb the water.

4. 

   Spread a small amount of toothpaste on the iron. Be sure to use white toothpaste instead of gel cream; White toothpaste gives a better foaming effect than gel cream. You should only use a coin amount.
   • To increase the cleaning effect, you can mix toothpaste with a little baking soda and vinegar.

5. 

   Use a toothpaste rag all over the iron. Pay attention to clean the steam vents, because this is a place where many types of dirt can be easily formed. If the countertop is too dirty, you can also use a dishcloth or scouring sponge to scrub the stains away.
   • Avoid using metal scouring materials, as these will scratch the iron surface.

6. 

   Wipe the toothpaste off with a damp rag. Wipe thoroughly to make sure no residue toothpaste stains your clothes in the process.

7. 

   Use a cotton swab to finish cleaning the steam injection hole. Soak a cotton swab in a solution of 1 part vinegar and 1 part water. Use a cotton swab to wipe both the outside and the inside of the steam vents respectively. This way you can remove additional dirt.
   • Cleaning the steam vents will help make the iron run more smoothly.
   • Do not use paper clips or other hard metal objects to avoid scratching the steam vents.
   advertisement

Advice

• Be sure to check the manufacturer's instructions before attempting the above methods. Some irons require the right detergent.
• Either way, you should pour water into the iron according to the manufacturer's instructions and turn on the steam spray mode to clean the steam vents.