How to fill the pump with water before starting

Video: How to start pumping water with your new water pump motor.!

Content

Steps
Part 1 of 3: Preparing the System
Part 2 of 3: Flushing the System
Part 3 of 3: Shutting Down
Tips
Warnings
What do you need

The water pump runs under pressure and stops working if it is turned off for an extended period of time, for example during the winter. In order for the pump to start working again, it must be “filled before starting”. Water must be poured into the pump so that it gets as far as possible and this will create a pressure so that the water supply begins. While the methods differ depending on the type of water pump, the methods below for priming the pump before starting will show you how to do it.

Steps

Part 1 of 3: Preparing the System

1 Disconnect the power supply to the pump. You should not leave any device turned on while you are using it. Go to the base of the pump and make sure it is turned off.
2 Place a jig that provides access to the piping system. On the pool pump, this will be the filter mesh. If you are not working with a pool pump, use any jig close to the water tank.
3 Prepare a hose that can be connected to an independent water source. Water will flow through the hose and remove blockages, make sure clean water is supplied.
- Many people choose to use a garden hose or a hose from a washing machine connected to a garden hose. However, if your garden hose contains lead, be aware that you should not drink from it. If you are using it properly, make sure there is a way to filter the water after the hose.
4 Flush the hose to remove deposits. Run water through it, keeping a constant flow for a few seconds before closing it. This is especially important for a hose that is not normally used or has not yet been used this season.
5 Open all safety valves in the pump system. This will keep pressure from building up. Monitor pressure to make sure everything goes according to plan.

Part 2 of 3: Flushing the System

1 Insert the hose into the plumbing fixture. Place a filter mesh on the pool pump. If you are priming the pump before starting on a construction site, simply connect it to the fittings of the nearest water tank. You now have a source of water flowing into a new building or pool.
2 Turn on the water supply to the hose. At first, you can hear air passing through the system. This is fine.
3 Wait for the water to drain from the reservoir. Wait for the water to fill the reservoir, or maybe you have a water pressure gauge to measure the fill level. Install a filter mesh in the pool pump and close it with a lid.
4 Turn off the water in the hose. As soon as you see water coming out of the opposite end, turn off the water supply to the hose. This should take a few minutes.
- When the water stops flowing at the opposite end (where you get water), then the water system is already full.
- However, do not disconnect the hose and end up repeating the process if necessary.

Part 3 of 3: Shutting Down

1 Reconnect power to the pump and turn on the system. Let the pump run for about a minute. Be aware that the pump cannot operate if the pressure in the water tank remains at or above the pressure in the pump. This is why the system won't start.
- If you have opened the bypass valve, wait for water to flow through it and then close it.
2 Wait for the pump to complete a full cycle. If you turn it off naturally, it will fill up. If not, please fill it in again. Try supplying water to the recipient. If you hear that the water pump is on, you are up to the task.
3 Repeat all steps until the pump is full and doing its job normally. Under certain circumstances, you may have to repeat it one or more times.
- If you have a tubeless type water tank, try leaving the cistern open at the beginning of the procedure. Thus, the water that has spilled will enter the tank by pressing on the place of the trapped air on the pipe. However, when you see water pouring out of the pipe, turn it off.

Tips

Your goal when filling the pump with water is to restore pressure because the pump is absorbing water. Check your gauges periodically and if the pressure is not high enough or the pump is not working properly, repeat all steps again. It is normal to try to fill the pump with water several times.
When filling the pool pump with water, you can first fill the swimming pool before starting and then the main pipe. This can be achieved by turning the first diverter valve to the main pipe index, shutting off the water in this section, and the flowing water through the pool slag separators. Next, turn the drain valve away from the main drain indicator so that both it and the pool slag separators are open, and wait for the water to flow normally.
If you cannot find plumbing fittings (step 2) and you have a simple pump system, then you will need to make your own inlet valve. It can be made with a tee, clamp and multiple pipes and must be near a water source.

Warnings

Keep a close eye on your pressure gauge. Keep the exhaust valves open longer than you think is sufficient. It is better to keep the pressure at the same level than to allow it to rise to a dangerous level that could damage the pumping system.